MATERIAL HANDLING / PRACTICAL GUIDE

What to include in a telehandler hire brief

Describe the load, placement position and attachment so a supplier can assess a telehandler proposal.

Identify the load accurately

Provide the load's weight, dimensions, packaging and lifting or handling points. Explain whether weights are documented or estimated. A pallet of uniform products is different from an awkward assembly with an offset centre of gravity. Ask the supplier what further information is needed before proposing a machine; never turn an uncertain weight into a firm capacity assumption.

Map pickup and placement

Show the pickup area, travel route and final placement point. Record height and horizontal reach from the intended standing position, including obstacles that prevent the machine moving closer. The largest advertised capacity is not a promise at full reach. The proposed model, attachment and load chart need to be considered together by the responsible people.

Confirm attachment and ground interfaces

Forks, buckets and other attachments change how a task is performed. Identify the intended attachment and ask the supplier to confirm compatibility and the applicable operating information. Include gradients, ground condition, turning space and pedestrian interfaces in the brief. Request a site assessment where the available information is insufficient to establish suitability.

Plan the receiving sequence

Coordinate truck arrivals, laydown space and installation timing. A machine booked for a short unloading window may sit idle if deliveries are late or loads are inaccessible. Agree waiting-time treatment, operator arrangements and the fallback plan if the nominated machine becomes unavailable. Keep substitutions subject to a fresh suitability check.

  1. Describe the task
  2. Check constraints
  3. Confirm model
Choose equipment from the job requirements, then confirm the exact configuration with the supplier. Original hire-desk planning diagram.
ILLUSTRATIVE SCENARIO · NOT A CUSTOMER CASE STUDY

Put the decision into practice

A builder wants to place a pallet beyond the edge of a slab. The pallet mass is known, but the first enquiry does not state how far the machine must stand back. The revised brief includes load dimensions, centre of gravity information where available, the required placement height and horizontal reach, and the proposed attachment. The supplier is asked to check the exact configuration against its load chart. The team also confirms the ground and setup position with the responsible site personnel. This changes the question from whether a machine can lift the mass somewhere to whether the proposed configuration can perform this particular placement.

What to compare for this task
SituationCheck thisAvoid relying on
Pallet placementMass, load centre, height and reachNominal maximum capacity
Different attachmentMatching chart and approved combinationFork chart for every attachment
Changed setup positionReassessed reach and groundReusing the original assumption

A mistake to avoid

A load below the headline capacity may still be outside the permitted envelope at the required reach. Do not interpolate a capacity or substitute another model's chart; obtain the correct documentation and competent assessment.

Example enquiry wording

Please assess [load mass and dimensions] placed at [height/reach] using [attachment]. The proposed setup is shown in the sketch. Confirm the exact model, attachment and applicable load chart, plus site information needed before selection.
Build and download your enquiry →

Include these in your enquiry

  • Load weight and dimensions
  • Pickup and placement positions
  • Attachment and model confirmation
  • Delivery sequence and waiting terms

Use these prompts to prepare a discussion. Confirm the actual equipment, site requirements and commercial terms with your supplier and the people responsible for the work.

Practical answers before you hire

Can I choose by maximum lifting capacity?

Not on that figure alone. Capacity changes with configuration and reach; have the supplier assess the task against the correct model and attachment information.

Does maximum lift capacity apply at full reach?

Do not assume it does. The applicable chart describes capacity for the configuration and operating position.

Why does the attachment matter?

Its geometry and mass affect the arrangement. Ask for the approved combination and matching capacity information.

What if the standing position changes?

Recheck the resulting reach and setup before work. A small site change can invalidate the original equipment selection.

Sources and editorial method

How AI assistance, sources and editorial examples are used · Report a correction

Prepared by Machinery Hire Directory. Source checked 24 September 2026. Scenarios, comparison prompts and enquiry examples are original editorial illustrations; they are not reports of completed projects or supplier quotations.

Genie — choosing telehandler size ↗

The linked source provides background. Supplier terms apply to that supplier, and model guidance does not replace the applicable local requirements or equipment documentation. No independent technical reviewer is claimed.

Equipment related to this guide